Bolens 1026 Bedienungsanleitung

Balsns/lodels824A 24", 8 HP102626", 10 HP1993 Garden Way Inc.$4.50Owner/OperatorManualSnowthrowers• Safety• Assembly• Controls• Operatio

Assembly (continued)Wiring Harness Instailation1. Connect lead wire (AB, Fig. 3-4) to engine wiring harness connector. Plug lead wire into connector

Assembly (continued)Fig.3-7ControlsWheel Drive Control LeverWheel drive control lever (C, Fig. 4-1) is iocated on top of left-hand handlebar tube in f

Controls (continued)Discharge snow in the same direction the wind is blowing (as long as it is safe to do so). As you change directions while throwing

Controls (continual)Fig. 4-6Section 5OperationPre-Start Checklist1. Review "Safety" and "Controls".2. Check unit for loose or mi

Operation (continued)starting1. Turn ignition key to RUN.2. Move choke knob to FULL CHOKE (warm engines require little or no choking). Push pre-star

Operation (continued)jËk CAUTIONUnit must be completely stopped while shifting. Damage to transmission will result if this instruction is not followed

Operation (continued)Snowthrowing PatternsUse pattern in Fig. 5-1 when snow cannot be thrown to one side. Begin throwing snow closest to the side wher

SectionsMaintenanceChecking and adding oil1. Shut engine off. Unscrew oil fill cap/dipstick (AM, Fig. 6-1) and wipe with clean, lint-free cloth.2. R

Maintenance (continued)LubricationAt the beginning and end of each season or after every 25 hours of operation, iubri- cate unit as recommended beiow.

Maintenance (continued)Wheel Drive Belt ReplacementTo replace wheel drive belt:1. Remove two bolts (AG, Fig. 6-4) and belt cover from unit.2. Remove

Thank you for purchasing this product. We believe you now own one of the finest snowthrowers available.This is a safety, operation and general mainten

Maintenance (continued)A. Loosen jam nut (M) seated against adjuster (N) on lower end of control rod. Turn adjuster (N) up the rod to increase spring

A/iaintenance (continued)0.125"-0.060" (3- 15 mm)Fig. 6-12Fig. 6-1319

Maintenance (continued)Maintenance ChartIntervalItemServiceBefore each useEngine oil Check level and conditionAll fastenersCheck for tightnessAuger dr

Maintenance (continued)rroubleshootingTROUBLEPOSSIBLE PROBLEMSOLUTION ngine won't startIgnition key in OFF positionTurn key to ON positionChoke k

Maintenance (continued)TROUBLEPOSSIBLE PROBLEMSOLUTIONAuger drive lever does not actuate augerBroken square key on engine drive pulleyBroken woodruff

SpecificationsSpecificationsBelow is a list of specifications for your snowthrower. The information is the most current at the time this manual was pr

LIMITED WARRANTYI. PRODUCTS COVEREDThis warranty applies to all Bolens® branded equipment. Troy-Bilt® branded tractors, mulching mowers, snow casters

Service InformationUnit Service and RepairTo service your unit, contact a factory-authorized dealer. Provide the dealer with the unit's model/ser

Section 1SafetyImportant!Safe Operating Practices For This SnowthrowerAThe triangle with an exclamation mark inside is a safety alert symbol. The safe

Safety (continued)5. If unit should vibrate abnormally, stop engine, disconnect spark plug wire and prevent it from touching spark plug. Remove key f

Section 2Attachments & KitsBelow is a list of attachments and kits available for your snowthrower. The information is the most current at the time

SUPPLEMENT TO THE SAFETY AND OPERATION INSTRUCTIONS MANUAL FOR BOLENS® LARGE FRAME SNOWTHROWERS MODELS 62A, 824, 824A, 1026 AND 1032(This information

IMPORTANT PRODUCT NOTICE

Assembly (continued)Spring should now be approximately 11/16" +/-1/16” (17 mm +/-1.5 mm) longer. If not:A. Loosen jam nut (JJ) and thread upward